Yanhua Mini ACDP + Module 27 Read BMW MSV90 DME ISN

Yanhua Mini ACDP + Module 27 supports reading, writing, and cloning BMW E/F chassis ISN without having to open the DME shell. Apply to MSV80, MSD80, MSD81, MSD85, MSD87 MSV90 Continental/ SIEMENS DME types.

This is reading BMW MSV90 DME ISN on the bench as an example, follow the post carefully to learn how to do it. To check the connection diagram, please click "Help".

Check the full video to learn:

Accessories

BMW MSV90 DME Module

MSV90 interface board

20PIN cable

ACDP host

OBD+ICP adapter

Install the MSV90 interface board.

Short the CAN resistor on the OBP+ICP adapter to the CAN-R-Join side.

Connect the MSV90 DME & ACDP host.

Operation

Mini ACDP >> BMW >> DME ISN >> BENCH Mode read/write DME ISN >> SIEMENS/Continental DME >> Fxx >> N52(MSV90) >> Read ISN >> Continue

Confirm the system info and save the screenshot.

Please take a screenshot and export the ISN data.

Export >> Save >> OK

ISN data is exported successfully.

Reading ISN data finished.

www.obd2shop.co.uk

Yanhua Mini ACDP Program JLR(2015-) KVM Add Key/All Keys Lost

This is a tutorial on using Yanhua Mini ACDP + Module 9 to program Land Rover 2010-2019 KVM add key & all keys lost. Users can click "Help" in app to check the connection info.

Normally, Land Rover's KVM module is at the left side or right side of the vehicle trunk. Jaguar's KVM is at the right side of the rear seat or in the front of the passenger seat.

Preparation

Blank key

BAV-KEY adapter

KVM interface board

ACDP host

Copper pillar

OBP+ICP adapter

20PIN cable

KVM module

1.Install the copper pillar, align D1-D4 test points. As long as the 4 test points are aligned, then all test points are aligned.

2.Lock the board with PCB lock & copper pillar. Connect the OBP+ICP adapter & KVM interface board. 

3.Connect the adapter & ACDP host, power up ACDP.

Operation

Mini ACDP >> Jaguar/ Land Rover >> ICP Add key/All key lost(2015-) >> KVM ICP(MC9S12XEQ384) >> Add key auto mode

Note:

1.Please prepare the OBP+ICP adapter, KVM interface board, KVM module, BAV adapter and blank key.

2.Save the original EEPROM, DFLASH data& the ones after programming the keys according to the software prompt.

3.ACDP device is forbidden to be powered off during the process of adding a key, otherwise it will cause the key to fail to be added.

Precautions:

1.Ensure the well connected for ACDP device, OBP+ICP adapter, KVM interface board & KVM module.

2.Follow the software prompts to save the chip data read from KVM module.

Pin detection passed. If the detection fails, please check and clean the test points.

Press "Continue".

It is detected that the KVM module chip has been encrypted. Press "Continue".

Please save the original PFLASH data of the KVM module.

Please save the original EEPROM data of the KVM module. 

Please save the original DFLASH data of the KVM module.

Check the VIN number and other vehicle info, press "Continue".

Note:

1.To maintain the ACDP device power-on state, first disconnect the OBP+ICP adapter from the ACDP device(keep the OBP+ICP adapter, KVM interface board and KVM module connected).

2.Then connect the ACDP device to the BAV-KEY adapter and place the programming key correctly on the BAV-KEY adapter.

Current key ID: 822D4E37

Choose the unoccupied key ID displayed as 000: Key3

Please save the EEPROM data of the KVM module after adding the key.

Please save the DFLASH data of the KVM module after adding the key.

Note:

1.Keep the ACDP device powered on. First disconnect the BAV-KEY adapter from the ACDP device.

2.Then connect the ACDP device, OBP+ICP adapter, KVM interface board and KVM module to ensure normal communication.

Continue >> Continue

Check the IMMO info. As you can see, the new key ID is in the key list.

Writing chip...

Adding the key completed.

Please install KVM module to the car and confirm that the new key can be used normally!

OK >> OK

This is how to use Mini ACDP JLR KVM Module for key programming.

www.obd2shop.co.uk

Fixed: Yanhua Mini ACDP WiFi Connection Fails When Binding

Problem: My new Yanhua Mini ACDP is unable to bind in app, it prompted: "WiFi connection fails. Please check the phone is WIFI connection and whether the WiFi name and password are correct. Then retry the initial use settings."

I'm sure the WiFi name and password are all correct. 

What's the reason? Any advises?

Solution

Modify the WiFi name to be shorter. Then try again. Cause Mini ACDP may fail to identify in case WiFi name is longer.

Hope this is helpful.

Technical support

www.obd2shop.co.uk

JLR ZF-9HP gearbox clone (BOOT) via Yanhua Mini ACDP

ACDP module 28 supports Jaguar, Land Rover, Chrysler, Dodge, Fiat, Honda, Jeep, and other models of the ZF-9HP gearbox computer BOOT mode clone.

This post will take JLR as an example to make the ZF-9HP gearbox cone with ACDP Master and module 28.

Check all the accessories we need.

Step 1. Connect and install

Disassembling the ZF-9HP gearbox computer case.

Remove the 3 screws of the interface board.

Install the copper pillars.

Put the CPU positioning frame on the CPU.

Install the ZF-9HP BOOT interface board. Then lock the board with copper pillars.

Install the ZF-9HP Port interface board, and connect two interface boards with an 8PIN cable.

Connect the OBP+ICP adapter with the 20PIN cable.

Short the CAN resistor on the OBP+ICP adapter to the "CAN-R-JOIN" side.

Connect the ACDP host.

For more detailed installation steps, please refer to the video:

Step 2. Identify

Open ACDP APP, select "Jaguar/LangRover" >> "Gearbox Clone" >> ZF-9HP(BOOT)

Choose "Identify", confirm system information, and click "Continue".

BOOT point pin detection passed, click"Continue".

Confirm the system information and click "OK".

Identify system info finished.

Step 3. Full Backup Data

Choose "Full Backup Data", BOOT point pin detection passed, and click"Continue".

Confirm system information, and click "Continue".

Reading chip data...

Save chip data, and click "OK".

Reading chip data finished.

Step 4. Full Write Data

Connect another ZF-9HP gearbox computer.

Then choose "Full Write Data"

BOOT point pin detection passed, click"Continue".

Confirm system information, and click "Continue".

Select chip data: click the chip data file saved in Step 3.

Ready to write chip data, please don't cut the power nor pull out the device during the programming!

Writing chip data...

Writing chip data finished.

https://www.obd2shop.co.uk/

Yanhua Mini ACDP data export Operation Guide (iOS system)

This article will guide you on how to export Yanhua Mini ACDP data to send to technicians for analysis when you encounter problems.

Step 1. Open the ACDP software and click "Me"

Note: ACDP software version requires 1.9.7 or higher.

Step 2. Select "My File" => "Menu" => "List" => "ATmatch"

Step 3. Click on the symbol on the right side of the folder you need to export, then click "Zip".

Note: Folders must be compressed before they can be exported. The data can be exported directly.

Step 4. Click on the symbol to the right of the zip package, then choose "Share".

Step 5. Select the APP you want to share with, then "Sent to chat" to complete the sending.

For more information about Yanhua ACDP, please follow https://www.obd2shop.co.uk/

Yanhua Mini ACDP Refresh Mercedes 272/273 ME9.7 DME

Yanhua Mini ACDP + Module 18 can support to refresh Mercedes Benz CR4.XX/ CRD2.XX/ CR5/ ME9.7/ SMI271KE2.0/ CRD.11/ SIM271DE2.0/ CR3.XX/ SIM4LKE/ MED17.7X/ CR6/ SIM266 DME. For board mode, need to buy MB DME/ISM Refresh together.

Following is a quick demo on Benz 272/273 ME9.7 DME refresh.

Read to learn:

Connection

1. Insert the PECU into the test point of the DME according to wiring diagram

2. Connect PECU to ACDP

Operation

Mini ACDP App >> Benz >> DME refresh >> ME9.7 >> Refresh >> Continue

Take screenshot vehicle info.

At this time, the state are uncleared with "YES".

Continue >> OK >> Automatic calculation erase password >> Continue

The online password calculation is about to begin. During the password calculation process, it is forbidden to unplug or plug the device and please keep the device connected to Internet!

Click "Continue".

Ready to erase data, please don't cut the power nor pull out the device during the programming!

Click "Continue".

Erase system data finish.

OK >> OK

Identify >> Continue >> OK >> OK

The state have cleared with "NO".

Identify system info finish.

Save data file success.

http://blog.obd2shop.co.uk/yanhua-mini-acdp-refresh-mercedes-272-273-me9-7-dme/

Yanhua Mini ACDP Module 28: Clone ZF-9HP Gearbox

Latest Yanhua Mini ACDP Module 28 can clone ZF-9HP gearbox in BOOT mode. Supports Jaguar, Land Rover, Chrysler, Dodge, Fiat, Honda, Jeep, etc. Need to work with Mini ACDP basic module.

Features

1. The Interface board can be inserted blindly to align with the boot test point, no need magnifying glass for calibration or complex probe workbench operation.

2. It's more safer and reliable to use BOOT test point with pin detection function, data read & write.

3. It's more simple & efficient to use special interface board rather than cables.

Why buy Mini ACDP Module 28?

Traditional BOOT mode: 

- Boot point needs to be aligned by human eye with magnifying glass;

- Cable connection is risky to damage module due to misoperation.

ACDP BOOT mode:

- Interface board blind insertion

- Boot test point with pin detection function.

www.obd2shop.co.uk

Yanhua Mini ACDP Module 27: Read/Write BMW DEM ISN & Clone

Yanhua Mini ACDP Module 27 is supported to read/write ISN & clone BMW E/F chassis MSV80, MSD80, MSD81, MSD85, MSD87, MSV90 DME. Must work with Mini ACDP basic module on a smart phone. Compatible with Android & iOS system.

Features

1.Fast reading/writing ISN & clone DME on bench without having to open the shell or program DME.

2.Special interface board is more convenient than wire connection, easier and safer, more efficient and reliable.

Support DME type: Continental, SIEMENS

Mini ACDP APP Operation Steps

Step1. Connect

Step2. Read/write data

Step3. Disconnect

Yanhua ACDP BMW allows to backup & write data, read & write MAPS, INT/EXT EEPROM, modify ISN data.

How to connect Module 27?

1. Prepare ACDP, OBP+ICP adapter, interface board & BMW DME.

2. Connect the interface board correctly to the DME interface as shown.

3. Short the CAN resistor on the OBP + ICP adapter to the "CAN-R Join".

4. Connect all together.

BMW MSV80

BMW MSD80/MSD81

BMW MSD85/MSD87

BMW MSV90

http://blog.obd2shop.co.uk/yanhua-mini-acdp-module-27-read-write-bmw-dem-isn-clone/