How to Disassemble VW 5C Magotan Key Inner Shell Using Vtool

This guide shows how to use the YANHUA Vtool 5C/5D Key Cutting Kits to safely disassemble the VW 5C Magotan key inner shell.

Preparation

Before starting, prepare all the required dismantling tools from the kit.

Important: The induction coil inside the key is very sensitive. Be careful during the whole process and do not damage it.

Step 1: Remove the Screws

First, remove the two screws from the key shell.

This makes it easier to observe the cutting position during the disassembly process.

Step 2: Fix the Key in the Holder

Place the key into the holder.

Make sure the white side is facing toward you.

Tighten the holder firmly to secure the key.

Step 3: Cut the First Weld Seam

Tilt the blade slightly.

Align the blade edge with the weld seam on the upper-right corner.

Use a hammer to gently strike the blade and open the weld seam.

Continue cutting left along the weld seam.

Note:

There are support posts at each corner inside the shell.

Do not cut too deeply — a shallow cut is enough.

Once completed, the first side is finished.

Step 4: Cut the Vertical Side

Stand the key upright and secure it firmly.

Tilt the blade again and align it with the weld seam.

Continue cutting carefully along the seam.

After finishing this section, move to the opposite side.

Step 5: Cut the Other Side Carefully

When cutting near the induction coil area:

Do not cut too deep.

The blade depth should be close to the height of the black edge only.

Continue cutting to the left along the weld seam until this side is complete.

Step 6: Handle the Induction Coil Area

Finally, work on the weld seam near the induction coil.

Attention:

Do not cut beyond the black edge; the induction coil may be damaged.

Carefully continue cutting the weld seam.

Step 7: Pry Open the Back Cover

Use a prying tool to gently open the back cover.

Then remove the keyboard board from inside the shell.

The disassembly VW the VW 5C Magotan key inner shell is now complete.

Video guides:

For further technical assistance: www.obd2shop.co.uk

How to Disassemble a VW 5C Folding Key Step by Step

In this guide, we will show you how to use the Yanhua Vtool 5C/5D Key Cutting Kits to safely disassemble a VW 5C folding key step by step.

The process is simple if you use the correct tools and follow the proper sequence.

Required Tools

Prepare the following tools from the Yanhua Vtool kit:

Internal snap ring pliers

Flathead screwdriver

T6 Torx screwdriver

Step 1: Open the Mechanical Key

First, flip out the mechanical key blade.

You will find a locking clip inside the key shell. Use the internal snap ring pliers to carefully pry open the locking clip.

Then open the surrounding section and remove the back cover.

Step 2: Remove the Battery and Screw

Use a flathead screwdriver to remove the battery.

Next, locate the internal screw and remove it with a T6 Torx screwdriver.

Place your finger on the left side of the key base and push firmly to the right to separate the base easily.

Step 3: Open the Side Cover

Insert a flathead screwdriver into the side gap at a 90 ° angle.

Carefully apply upward force with the screwdriver shaft to pry open the side cover.

After that, insert the circlip pliers into the gap and slowly separate the key's inner housing.

Remove the shell completely.

Step 4: Remove the Keyboard

Use a flathead screwdriver to gently lift the keyboard section.

Carefully remove the keyboard from the housing.

The VW 5C folding key disassembly is now complete.

Video Guide

Watch the complete operation video here:

Source

For more automotive locksmith tools and key cutting accessories, visit: www.obd2shop.co.uk

How to Disassemble Golf 8 5D Key Shell with Yanhua Vtool

When working on VW Golf 8 smart keys, proper disassembly is important to avoid damaging the key shell or internal components. In this guide, we’ll show you how to use the YANHUA Vtool 5C/5D Key Cutting Kits to safely disassemble a VW Golf 8 5D key housing step by step.

Step 1: Remove the Mechanical Key

First, take out the flathead screwdriver stored inside the kit.

Press the side button on the key.

Remove the mechanical key.

Insert the flathead screwdriver into the mechanical key slot.

Push upward gently to remove the back cover.

Remove the battery.

Step 2: Release the Locking Clips

Insert the screwdriver into the gap near the locking clip.

Pry upward carefully to pop the locking clip open.

Locate the second locking clip.

Insert the screwdriver into the gap and push forward to release it.

Pry open the side locking clip as well.

Insert the screwdriver into the side gap and lift the side frame upward.

At this point, you will see the inner key shell separated from the outer frame.

Remove the button panel.

Step 3: Separate the Key Shell

Insert the screwdriver into the indicated position.

Continue prying toward the key shell carefully.

Repeat the motion several times until the shell is completely released from the latch pin.

The VW Golf 8 5D key housing disassembly is now complete.

Video Guide

For a detailed visual demonstration, watch the video below:

Conclusion

Using the YANHUA Vtool 5C/5D Key Cutting Kits makes VW Golf 8 5D key shell disassembly easier and safer. By following the correct prying sequence and carefully releasing the locking clips, you can avoid damaging the key housing and complete the job efficiently.

For more automotive locksmith tools and key programming products, visit:

www.obd2shop.co.uk