How to perform authorization of the Yanhua Mini ACDP module

This article will guide you on how to authorize the Yanhua Mini ACDP module automatically.

Here are the steps:

The new module has an authorization code sticker on the outside.

Please peel off the green protective film.

If the authorization code is covered with residual gel, remove it with an eraser.

Make sure the QR code is clearly visible.

Open the ACDP APP and check that the ACDP device is connected correctly.

Click "Me" in the lower right corner and choose "Module List".

Click "Add" in the lower left corner, then click "Scan QR Code" to continue.

The authorization card number will be filled in automatically.

You can also manually enter the authorization card number.

Please note that letters must be capitalized.

Check the authorization card number, make sure it is correct and click "Submit".

The authorization is successful!

Video guide:

Ford DPS6/MPS6 Gearbox Clone with Yanhua Mini ACDP

This is a tutorial on how to clone Ford DPS6 & MPS6 gearbox module with Yanhua Mini ACDP step by step. The MPS6 gearbox clone procedure also applies to Volvo, Land Rover, Chrysler, Dodge, etc.

How to Clone Ford DPS6 Gearbox?

Tip: Click "Help" to view the connection diagram before operation.

Accessories Required:

Ford DPS6 gearbox module

20PIN cable

OBP+ICP adapter

ACDP host

Module 26 Ford DPS6 interface board

Connection

1. Install the interface board.

2. Short the jumper cap on the OBP+ICP adapter to the "CAN-R" JOIN side.

3. Connect to ACDP together

Operation

Step1. Backup Original Data

Mini ACDP >> Ford >> Gearbox clone >> DPS6 >> Connect >> OK

Please ensure a stable network connection.

DO NOT pull out the device during working.

Click "Continue".

Check system info,

Continue >> OK >> OK >> OK

Read/write data >> Full backup data >> OK >> Continue

Save chip data.

Reading chip data finished.

Return back to the previous page.

Disconnect >> OK >> Continue

Disconnect finished.

Step2. Write to New Gearbox

Connect the new DPS6 gearbox module & prepare to write the original data.

Connect >> OK >> Continue >> Continue >> OK

Connect system finished.

Read/write data >> Full write data >> OK >> Continue >> Load original data file

Ready to write chip data, please don't cut the power nor pull out the device during the programming!

Click "Continue".

Writing chip data finished.

Return back to the previous page.

Disconnect >> OK >> Continue

Disconnect finished.

Completed!

How to Clone MPS6 Gearbox?

Tip: Click "Help" to view the connection diagram before operation.

Accessories Required:

MPS6 module

OBP+ICP adapter

ACDP host

20PIN cable

Module 14 MPS6 interface board 

Connection

1. Install the MPS6 interface board.

2. Short circuit the CAN resistor on the OBD+ICP adapter to the "CAN-R" JOIN side.

3. Connect ACDP, OBP+ICP adapter & MPS6 gearbox.

Operation

Step1. Backup Data

Mini ACDP >> Jaguar/Land Rover >> Gearbox clone >> Freelander >> MPS6 >> Full backup data >> Continue

Remember to save module info, click "Continue".

Save chip data file.

Backup chip data finished.

Step2. Write Data

Connect the new MPS6 gearbox & prepare to write the original data.

Full write data >> Continue >> Continue >> Load chip data file

Ready to write chip data, please don't cut the power nor pull out the device during the programming!

Writing chip data finished.

Completed.

http://blog.obd2shop.co.uk/ford-dps6-mps6-gearbox-clone-with-yanhua-mini-acdp/

Benz VGS-NAG3 9GTronic Gearbox Clone via Yanhua Mini ACDP

How to clone Mercedes Benz VGS-NAG3 9GTronic gearbox with Yanhua Mini ACDP + Module 16? Follow this guide to learn how to do it.

Note: click "Help" to check the connection diagram.

Tools Required

VGS-NAG3(9 Tronic) gearbox

PTCU cable

DB15-LAN adapter

SH725XX interface board

ACDP host

Installation

1. Install the interface board.

2. Short circuit the CAN resistor on the DB15-LAN adapter to the "CAN-R" side.

Operation

Mini ACDP >> Benz >> Gearbox clone/refresh >> C class >> VGS-NAG3(9GTronic) >> Full backup data

Connect ACDP with the gearbox.

Remember the BOOT version & Bosch number. These 2 numbers of new gearbox should be same as original one.

Save chip data file.

Connect the new VGS-NAG3(9Tronic) gearbox.

Full write data >> Continue >> Check BOOT version & Bosch number, continue.

Select chip data file to write.

Write data finished.

Completed!

Read also:

Mercedes Benz VGS2-NAG2 Gearbox Refresh with Yanhua Mini ACDP

GM 6L50 Gearbox Clone via Yanhua Mini ACDP and Module 22

Yanhua Mini ACDP with Module 22 can support GM 6TXX / 6LXX gearbox clone, this article will take GM 6L50 as an example to guide you on how to do it.

The accessories we need:

20 PIN Cable

OBP+ICP Adapter

ACDP Host

6LXX Interface Board

Connect the ACDP, OBP + ICP adapter, interface board and gearbox as the picture shows.

Open the Mini ACDP APP, choose "GM" → "Gearbox clone" → "GM 6L50"

Backup chip data

Choose "Full backup data", and make sure the gearbox is connected with ACDP.

Confirm the system information and save the screenshot, click continue.

After the clip data has been read successfully, click "Save" in the lower right corner.

Write chip data

Choose "Full Write data", and make sure the gearbox is connected with ACDP.

Confirm the system information and save the screenshot, click continue.

Select the original data file that saved in the previous step.

The device is about to write clip data, please make sure these two gearbox computers' model are the same.

Writing chip data finished.

For more detailed steps, please refer to the video:

Yanhua FEM/BDC Special Programming Clip for 95128/95256 Chip

Yanhua FEM/BDC Special Programming Clip is designed to pre-process BMW FEM/BDC module without having to remove or solder 95128/95256 chip. With it, you don't need to worry about how thick the paint on the chip!

Highlights

 Fast clamping

 Safe & reliable

 Simple positioning, not easy to slip.

 Easy to solve the problem of chip paint thick & puncture socket slip off.

 Compatible with Yanhua Mini ACDP, CGDI, VVDI, Autel, Launch X431. 

How to install FEM/BDC Special Programming Clip?

1. Insert the 2 screws of the special programming clip into PCB plate holes.

2. Lock the PCB lock.

FEM connection diagram

BDC connection diagram

http://blog.obd2shop.co.uk/yanhua-fem-bdc-special-programming-clip-for-95128-95256-chip/

Mercedes Benz VGS2-NAG2 Gearbox Refresh with Yanhua Mini ACDP

This article will guide you on how to do a Mercedes Benz VGS2-NAG2 gearbox refresh with Yanhua Mini ACDP and its module 16.

Tools need:

VGS2-NAG2 gearbox

VGS2/3-NAG2 interface board

20PIN cable

OBP+ICP adapter

ACDP host

Step 1. Connect the tools mentioned above.

Correctly connect the interface board to the gearbox interface as shown.

Short the CAN resistor on the OBP + ICP adapter to "CAN-R Join".

Connect ACDP, OBP+ICP adapter, interface board and VGS2-NAG2 gearbox.

Step 2. Perform Benz VGS2-NAG2 Gearbox Refresh

On the Mini ACDP main interface, select "Benz" → "Gearbox clone/refresh" → "C Class" → "VGS2-NAG2" → "Refresh", make sure the ACDP device is connected to the gearbox and click to continue.

Check personalized and activated are YES, which means the gearbox has not been refreshed.

Confirm the system information, then click continue.

Follow the instructions to perform the operations, and erase system data finish.

Choose "Identify", make sure the ACDP device is connected to the gearbox and click to continue.

Make sure "Personalized" and "Activated" are "NO", which means the gearbox data has been erased.

Identify system information finish.

Reference video:

Yanhua Mini ACDP + Module 13 Clone VW Audi VL381(0AW) Gearbox

This is a tutorial on how to use Yanhua Mini ACDP + Module 13 clone Volkswagen/ Audi VL381(0AW) gearbox. Module 13 also supports DQ200(0AM/0CW), DQ250(02E/0D9), DL382(0CK), DL501(0B5) models as well.

Read also:

Yanhua Mini ACDP + Module 13 Clone VW Audi DQ200/250 Gearbox

Check full operations on Youtube:

Operation Process

To check connection diagram, please click "Help".

Please make sure the model & SN is correct;

Tool Required:

VL381 gearbox

VL381 interface board

20PIN cable

OBP+ICP adapter

ACDP host

Install the interface board. Short circuit the CAN resistor on the OBP+ICP adapter to the "CAN-R-JOIN".

Step1. Read & Backup Data

Mini ACDP >> VW >> Gearbox Clone >> Audi >> VL381(0AW) >> Full Backup

1. Please connect ACDP with the gearbox.

2. This function needs to be connected to the Internet. Please make sure the network is good.

Confirm the gearbox model, press "Continue".

Read to read chip data, press "OK".

Please save the chip data, press "OK".

*(Please noted the file name contains gearbox model & operation time)

Step2. Write Data

Connect the new VL381(0AW) gearbox.

Full write >> OK >> Continue >> OK >> Load data file

Data wrote successfully!

Completed.

http://blog.obd2shop.co.uk/yanhua-mini-acdp-module-13-clone-vw-audi-vl3810aw-gearbox/